Shop
- $179.53The Ultimate package: 3" PolyFlex tire mounted on a 2-piece, bolt-on rim with cast hub & spokes. Long lip life. Flexible to shed mud and follow the ground contour. Complete, mounted, bolt-on assembly for easy, fast installation. Durable, cast spokes offer the widest opening possible to shed mud and debris.$6.50LEGACY P/N WAS T 32 B – EX10276 – Bushing (spacer for bearing)$137.502.5 inch. If you need taller pipes to improve gravity flow thru the secondaries, or just looking to replace rusted-out pipes or older pipes that lack dimples to redistribute seed & fertilizer more uniformly as it goes up into distribution head. Other sizes available. LEGACY P/N WAS SMA.Riser63.BLK – Riser pipe 2.5″ BLK$135.00Atom-Jet seed boot/scraper (Case P-500/NH 2080, right or left). These carbide-protected replacement scrapers for the single shoot version of these drills are made from a long-lasting abrasion resistant plate to extend the life of the scrapers. The two sets of mounting holes allow for the scrapers to be adjusted up as the disk wears down.… Read More »SCRAPER-SINGLE SHOOT RH, ATOM JET, CASE IH P500 / NH 2080$269.25Keeton + Mojo + Keeton mounting bracket kit + closing bracket kit + Thompson wheel.$72.50Left Aricks Depth CONTROL Arm. Cast in Hi Tensile steel. The Hi Tensile stud is up-sized for added strength where the stud leaves the casting.$72.50Right Aricks Depth CONTROL Arm. Cast in Hi Tensile steel. The Hi Tensile stud is up-sized for added strength where the stud leaves the casting.$195.00For John Deere 90 and Pro-series openers. The gauge wheel axle kit from Aricks is the final piece in making your disc opener completely non-greasable! No more seized axles. Holds cast arms tight.$195.00For John Deere 90 and Pro-series openers. The gauge wheel axle kit from Aricks is the final piece in making your disc opener completely non-greasable! No more seized axles. Holds cast arms tight.$35.002x thickness of OEM. Straight-across depth selection for easy adjusting. A durable, logical replacement for the light-duty, inferior criss-cross depth adjuster that rattles and wears out. A much-needed redesign of the traditional diagonal slotting for a simpler, heavy-duty system that will withstand tough conditions better than the OEM. Same depth increments as OEM.$40.00
For JD 90-series boots. Patented, simple, bolton device designed to fit between the main opener arm boot pivot flanges and the seed boot, eliminating the up and down movement of the seed boot and allowing for a consistent furrow and more even seed placement. Includes necessary hardware & new seed boot pivot pin.
$40.00For 50-series boots. Patented, simple, bolton device designed to fit between the main opener arm boot pivot flanges and the seed boot, eliminating the up and down movement of the seed boot and allowing for a consistent furrow and more even seed placement. Includes necessary hardware & new seed boot pivot pin.
All About Hydraulic Oil Coolers & Snorkel Kits
Stay cool; prevent clogging
Hydraulic oil coolers function by circulating oil through a radiator connected to a fan, which forces air over the radiator. This process cools the hydraulic oil while simultaneously warming the air entering the lines, helping to prevent clogging from sticky fertilizers and seed treatments. When run with a snorkel, it helps remove humidity by pulling drier air from higher up, which is also cleaner air, so you reduce the amount of dust and debris that could cover the radiator. Snorkel kits are available with or without the oil coolers, for air carts and air boom applicators.
Content of this page is copyright 2005-2024 Exapta Solutions, Inc. (reprint with written permission only).
Thompson wheel covered by U.S. Patent No. 6,907,833. Liquid delivery feature of Valion seed tube guards is U.S. Patent No. 8,978,564. Ninja seed bounce flap U.S. Patent Pending. UniForce U.S. Patent Pending. All rights reserved on other designs. Exapta is a registered trademark of Exapta Solutions, Inc. Keeton is a registered trademark of Precision Planting. Mojo Wire, Thompson wheel, Valion guard, Ninja flap, UniForce, DuraLok, No-till Seeding Explained, and No-till Seeding School are trademarks of Exapta. Disclaimer: Recommendations & page content are current, accurate, and believed to be broadly applicable as of the time of writing (Dec 2005) and last update (2005 – 2014). Because of diversity of soils, climate, crops, planter & drill models/designs marketed worldwide, combinations of attachments, etc., actual results may vary. No warranty is made as to actual results obtained. Should you encounter exceptions or worthwhile annotations to the statements made on this page, please contact us.
Derek Tjaden
Derek is Kansas native who grew up in a 100% no-till farming operation. From an early age the benefits of no-till were made known to Derek by his father and by attending no-till conferences. From there he furthered his passion for soils while at Kansas State University getting his agronomy degree. He has had the experience of working in various roles and sectors of agriculture from sales and consulting, to management, which have all been within production agriculture. Derek has also worked in specialty ag markets such as turf and ornamentals.
Bob Pagel
Sales & Service Representative
Prior to joining Exapta, Bob Pagel was an Agricultural Territory Sales Manager for Ritchie Brothers, serving parts of MN, WI and IA. He continues to support his family farm in SE Minnesota.
Jon Zeller
Current Product Engineer
Jonathan Zeller joined Exapta excited to return to working with no-till planting equipment. He supported research of no-till planting and other ag related projects for 7 years with Kansas State University’s Agricultural Engineering Department after getting his engineering degree. He later worked 3 years for Landoll Company, LLC. where he gained experience in a design engineering role. Jonathan grew up on a small family farm in NE Kansas working with row crops, hay and cattle. Jonathan enjoys solving engineering problems and improving or creating products to be robust and easy to install and service.
