Shop
- $9.36Flange/hub, alloy, for DuraLok firming wheel, smooth side (internal threads)$8.14Flange/hub, alloy, for DuraLok firming wheel, bolt head side with counterbores$55.0820% more wear life than OEM / Ingersoll / Bellota. The Forges de Niaux takes it to the next level with a unique steel and special heat-treat process. Same dimensions as OEM. Uses Peer double-row 205 bearings, whereas OEM and other aftermarket are double-row 204 bearings (smaller diameter). They also use 5/16" rivets instead of 1/4".$51.1820% more wear-life than the next-best, which was our old standby from Ingersoll-Canada. The Forges de Niaux takes it to the next level with a unique steel and special heat-treat process. Same dimensions as OEM. Replaces John Deere Part number N283804.$135.00Atom-Jet seed boot/scraper (Case P-500/NH 2080, right or left). These carbide-protected replacement scrapers for the single shoot version of these drills are made from a long-lasting abrasion resistant plate to extend the life of the scrapers. The two sets of mounting holes allow for the scrapers to be adjusted up as the disk wears down. The scraper mounts directly to the CNH shank making installation simple. The built-in trash shield is made from the same plate, preventing trash from dropping down inside the scraper, which is a significant improvement over the CNH tin shield that takes an extra set of hands to install.$57.21
Now available: Forges de Niaux’s superior blades for Case-IH Precision Disc 500 / NH P-2080 / 2085. Same dimensions as OEM, but with the greater durability of the Forges de Niaux! Harder on the periphery, for 20% greater wear life. Stays sharper longer. (Note: We don’t stock these in our warehouse; all orders will incur shipping.)
$47.92Forges de Niaux’s superior blades for JD MaxEmerge PLUS (Pre-XP) and Kinze. Same dimensions as OEM, but with the greater durability of the Forges de Niaux! Harder on the periphery, for 20% greater wear life. Peer 204 bearing and ¼" rivet. Stays sharper longer.
$64.65Forges de Niaux’s for John Deere XP & ME5. 15" x 3.5mm FDN Blade XP Gothic Arch 205 Bearing, Low Profile Cast Housing, Xtreme Duty to Fit John Deere (AA65248XDLPBA). Harder on the periphery, for 20% greater wear life & stays sharp longer. Uses a 205 single-row bearing in a seriously heavy-duty cast hub with larger rivets to give you extra clearance with gauge wheel rims. Limited inventory.
$5.86Small steel tab w/ threaded hole for screw, front of K.608 (Mojo Wire kit for Case P-500), includes screw with standard threads to match those machined into block.$45.00Install tool for firming & closing kits
$45.00Removal tool for firming & closing kits
$4.68Grade 8 washer (special ID) and grade 8 special flange locknut (smooth underside; no serrations) for closing arm pivot point, JD 50/60/90 drill. Corresponding OEM parts are only grade 5, and wear out fairly quickly, which creates side-play and lets the spring for the closing arm pop out of its setting too easily.All About Hydraulic Oil Coolers & Snorkel Kits
Stay cool; prevent clogging
Hydraulic oil coolers function by circulating oil through a radiator connected to a fan, which forces air over the radiator. This process cools the hydraulic oil while simultaneously warming the air entering the lines, helping to prevent clogging from sticky fertilizers and seed treatments. When run with a snorkel, it helps remove humidity by pulling drier air from higher up, which is also cleaner air, so you reduce the amount of dust and debris that could cover the radiator. Snorkel kits are available with or without the oil coolers, for air carts and air boom applicators.
Content of this page is copyright 2005-2024 Exapta Solutions, Inc. (reprint with written permission only).
Thompson wheel covered by U.S. Patent No. 6,907,833. Liquid delivery feature of Valion seed tube guards is U.S. Patent No. 8,978,564. Ninja seed bounce flap U.S. Patent Pending. UniForce U.S. Patent Pending. All rights reserved on other designs. Exapta is a registered trademark of Exapta Solutions, Inc. Keeton is a registered trademark of Precision Planting. Mojo Wire, Thompson wheel, Valion guard, Ninja flap, UniForce, DuraLok, No-till Seeding Explained, and No-till Seeding School are trademarks of Exapta. Disclaimer: Recommendations & page content are current, accurate, and believed to be broadly applicable as of the time of writing (Dec 2005) and last update (2005 – 2014). Because of diversity of soils, climate, crops, planter & drill models/designs marketed worldwide, combinations of attachments, etc., actual results may vary. No warranty is made as to actual results obtained. Should you encounter exceptions or worthwhile annotations to the statements made on this page, please contact us.
Derek Tjaden
Derek is Kansas native who grew up in a 100% no-till farming operation. From an early age the benefits of no-till were made known to Derek by his father and by attending no-till conferences. From there he furthered his passion for soils while at Kansas State University getting his agronomy degree. He has had the experience of working in various roles and sectors of agriculture from sales and consulting, to management, which have all been within production agriculture. Derek has also worked in specialty ag markets such as turf and ornamentals.
Bob Pagel
Sales & Service Representative
Prior to joining Exapta, Bob Pagel was an Agricultural Territory Sales Manager for Ritchie Brothers, serving parts of MN, WI and IA. He continues to support his family farm in SE Minnesota.
Jon Zeller
Current Product Engineer
Jonathan Zeller joined Exapta excited to return to working with no-till planting equipment. He supported research of no-till planting and other ag related projects for 7 years with Kansas State University’s Agricultural Engineering Department after getting his engineering degree. He later worked 3 years for Landoll Company, LLC. where he gained experience in a design engineering role. Jonathan grew up on a small family farm in NE Kansas working with row crops, hay and cattle. Jonathan enjoys solving engineering problems and improving or creating products to be robust and easy to install and service.
