Uncategorized
- $240.00LEGACY P/N WAS AJ FW200R - RIGHT Firming Wheel and Bracket for Case P500/NH2080 **Drop Ship from AJ**$58.55LEGACY P/N WAS C 102L - Complete firming kit, Case P-500 (LH), full length Keeton$40.00Keeton Seed Firmer, Low Profile Tail, Quick Attach. Mounts to seed disc opener shafts and lower seed tube pin. Fits John Deere MaxEmerge 2, MaxEmerge Plus, MaxEmerge Pro, MaxEmerge XP, MaxEmerge XP Pro and MaxEmerge 5 row units. LEGACY P/N WAS 109044 - Keeton Quick Attach Bracket and LP tail, JD$10.75Steel bracket for Keeton on CIH P500 drill and New Holland P2080-series. Includes 2 bolts and 2 nuts. LEGACY P/N WAS C 101L - Bracket Kit, 2-pc drill Keeton, fits CIH Precision 500, NH P2080,85, w/ bolts and nuts$1.68LEGACY P/N WAS ARI 007 - Flange Locknut and washer for firming pivot point$1766.09For use with Valions. High-temp semi-rigid plastic. COMPATIBLE EQUIPMENT: Planters, JD 1700 MaxEmerge 5, JD 1700 Series XP, JD 1700, 7300, 7200 Series (Pre-XP), JD 7000, 7100 Series, Kinze 4900, Kinze 3000 Series, Kinze 2000 Series" LEGACY P/N WAS L 1150FT - Plastic Tubing, 50' Uncut, Heat Resistant 1/4" OD$94.00Thompson Wheel T44 with stub shaft, for JD 60/90/Pro-series drills. Zinc plate finish, Bolt-on star wheel = cost-effective replacement stars. Made from military-grade armor plating, for even longer wear life. Includes 1 wheel, 4 bolts, 1 spindle/shaft. For orders of 32 or more, please call for freight truck pricing. US Patent No 6,907,833
All About Stainless Seed Tubes
Stainless Steel for Less Corrosion
If you’ve ever replaced tubes or boots that have corroded, you know how impossible they are to reuse. Ease of hose installation and removal with new design. Comes with stainless steel bolt to attach to seed boot and a SS hose clamp for easy attach/removal of secondary hose (no more fighting hose barbs to remove hose!). Available in Front Right, Front Left and Rear Seed Tubes.
Content of this page is copyright 2005-2024 Exapta Solutions, Inc. (reprint with written permission only).
Thompson wheel covered by U.S. Patent No. 6,907,833. Liquid delivery feature of Valion seed tube guards is U.S. Patent No. 8,978,564. Ninja seed bounce flap U.S. Patent Pending. UniForce U.S. Patent Pending. All rights reserved on other designs. Exapta is a registered trademark of Exapta Solutions, Inc. Keeton is a registered trademark of Precision Planting. Mojo Wire, Thompson wheel, Valion guard, Ninja flap, UniForce, DuraLok, No-till Seeding Explained, and No-till Seeding School are trademarks of Exapta. Disclaimer: Recommendations & page content are current, accurate, and believed to be broadly applicable as of the time of writing (Dec 2005) and last update (2005 – 2014). Because of diversity of soils, climate, crops, planter & drill models/designs marketed worldwide, combinations of attachments, etc., actual results may vary. No warranty is made as to actual results obtained. Should you encounter exceptions or worthwhile annotations to the statements made on this page, please contact us.
Derek Tjaden
Derek is Kansas native who grew up in a 100% no-till farming operation. From an early age the benefits of no-till were made known to Derek by his father and by attending no-till conferences. From there he furthered his passion for soils while at Kansas State University getting his agronomy degree. He has had the experience of working in various roles and sectors of agriculture from sales and consulting, to management, which have all been within production agriculture. Derek has also worked in specialty ag markets such as turf and ornamentals.
Bob Pagel
Sales & Service Representative
Prior to joining Exapta, Bob Pagel was an Agricultural Territory Sales Manager for Ritchie Brothers, serving parts of MN, WI and IA. He continues to support his family farm in SE Minnesota.
Jon Zeller
Current Product Engineer
Jonathan Zeller joined Exapta excited to return to working with no-till planting equipment. He supported research of no-till planting and other ag related projects for 7 years with Kansas State University’s Agricultural Engineering Department after getting his engineering degree. He later worked 3 years for Landoll Company, LLC. where he gained experience in a design engineering role. Jonathan grew up on a small family farm in NE Kansas working with row crops, hay and cattle. Jonathan enjoys solving engineering problems and improving or creating products to be robust and easy to install and service.
