Shop
- $7.40Unique forward bend to put more seeds in the bottom of the furrow. Incredible wear life; doesn’t break off like OEM and aftermarket flaps. Fits Standard and Extended Wear boots, but includes u-nut for non-threaded ext wear JD 50 & 90-series drill boots, 7/8 x 5″ (includes 1/4″x7/8″bolt). For Pro series boot, see different kit. US Patent 9,668,402 COMPATIBLE EQUIPMENT: JD 750, 1850 Drill, JD 90-series Drill For std wear boots listed below, see other Ninja seed flap kit w/o u-nut: N284044 - std wear boot RH 90 series, threaded hole N284045 - std wear boot LH 90 series - threaded hole LEGACY P/N WAS M 4708 - KIT-NINJA STD SEED BOOT FLAP, JD$79.95LEGACY P/N WAS GW 300 - 3" PolyFlex tire only$40.00Keeton Seed Firmer, Low Profile Tail, Quick Attach. Mounts to seed disc opener shafts and lower seed tube pin. Fits John Deere MaxEmerge 2, MaxEmerge Plus, MaxEmerge Pro, MaxEmerge XP, MaxEmerge XP Pro and MaxEmerge 5 row units. LEGACY P/N WAS 109044 - Keeton Quick Attach Bracket and LP tail, JD$10.75Steel bracket for Keeton on CIH P500 drill and New Holland P2080-series. Includes 2 bolts and 2 nuts. LEGACY P/N WAS C 101L - Bracket Kit, 2-pc drill Keeton, fits CIH Precision 500, NH P2080,85, w/ bolts and nuts$55.00Kit-DuraLok for 60/90 w/ Pro row unit and all N Series LEGACY P/N WAS FW 110 Pro - Duralok for Pro and N series$1.68LEGACY P/N WAS ARI 007 - Flange Locknut and washer for firming pivot point$0.20Reinforcement Bolt for Universal Bracket. 12-pack, small machine screws & nuts, reinforcement for Univ brkt, 8-32 x 1.5 machine screw & nut. LEGACY P/N WAS K 1483 - Machine screw & nut for Keeton Universal Brkt$80.20Kit-Removal Tool for Main-Pin Bushings, JD 50/60/90 drills, Air Hammer LEGACY P/N WAS ARI 003A - Updated Removal Tool for Main-Pin Bushings, JD 50/60/90 drills, Air Hammer$175.42Kit-Removal Tool for Main-Pin Bushings, JD 50/60/90 drills, Manual Tool Manual removal tool for the bushings of the front/main pin of JD 50/60/90 drill openers. Use this to pull the bushings out. Kit includes stainless tube brush to clean out dirt and rust. Also includes lubricant. FOR USE WITH IMPACT WRENCH LEGACY P/N WAS ARI 003M - UPDATED Removal Tool for Main-Pin Bushings, JD 50/60/90 drills, Manual Tool$11.00Kit-Mojo Wire, Flo-Rite, fits Universal & Scraper-Mount (was K215) LEGACY P/N WAS K 212 - Mojo Wire: Flo-Rite, fits Universal & Scraper-Mount brackets$20.00Kit-Mojo Wire, Dry Keeton Tails for Universal & Scraper - Mount (was K211) LEGACY P/N WAS K 211 - Mojo Wire for Liquid Keeton tails for Universal & Scraper-Mount$11.50Kit-Mojo Wire, Dry Keeton Tails - Universal & Scraper Mount (was K212) LEGACY P/N WAS K 212 - Mojo Wire, Dry Keeton tails, for Universal & Scraper-Mount
All About Hydraulic Oil Coolers & Snorkel Kits
Stay cool; prevent clogging
Hydraulic oil coolers function by circulating oil through a radiator connected to a fan, which forces air over the radiator. This process cools the hydraulic oil while simultaneously warming the air entering the lines, helping to prevent clogging from sticky fertilizers and seed treatments. When run with a snorkel, it helps remove humidity by pulling drier air from higher up, which is also cleaner air, so you reduce the amount of dust and debris that could cover the radiator. Snorkel kits are available with or without the oil coolers, for air carts and air boom applicators.
Content of this page is copyright 2005-2024 Exapta Solutions, Inc. (reprint with written permission only).
Thompson wheel covered by U.S. Patent No. 6,907,833. Liquid delivery feature of Valion seed tube guards is U.S. Patent No. 8,978,564. Ninja seed bounce flap U.S. Patent Pending. UniForce U.S. Patent Pending. All rights reserved on other designs. Exapta is a registered trademark of Exapta Solutions, Inc. Keeton is a registered trademark of Precision Planting. Mojo Wire, Thompson wheel, Valion guard, Ninja flap, UniForce, DuraLok, No-till Seeding Explained, and No-till Seeding School are trademarks of Exapta. Disclaimer: Recommendations & page content are current, accurate, and believed to be broadly applicable as of the time of writing (Dec 2005) and last update (2005 – 2014). Because of diversity of soils, climate, crops, planter & drill models/designs marketed worldwide, combinations of attachments, etc., actual results may vary. No warranty is made as to actual results obtained. Should you encounter exceptions or worthwhile annotations to the statements made on this page, please contact us.
Derek Tjaden
Derek is Kansas native who grew up in a 100% no-till farming operation. From an early age the benefits of no-till were made known to Derek by his father and by attending no-till conferences. From there he furthered his passion for soils while at Kansas State University getting his agronomy degree. He has had the experience of working in various roles and sectors of agriculture from sales and consulting, to management, which have all been within production agriculture. Derek has also worked in specialty ag markets such as turf and ornamentals.
Bob Pagel
Sales & Service Representative
Prior to joining Exapta, Bob Pagel was an Agricultural Territory Sales Manager for Ritchie Brothers, serving parts of MN, WI and IA. He continues to support his family farm in SE Minnesota.
Jon Zeller
Current Product Engineer
Jonathan Zeller joined Exapta excited to return to working with no-till planting equipment. He supported research of no-till planting and other ag related projects for 7 years with Kansas State University’s Agricultural Engineering Department after getting his engineering degree. He later worked 3 years for Landoll Company, LLC. where he gained experience in a design engineering role. Jonathan grew up on a small family farm in NE Kansas working with row crops, hay and cattle. Jonathan enjoys solving engineering problems and improving or creating products to be robust and easy to install and service.
